<noframes id="l9zfn">

<form id="l9zfn"><big id="l9zfn"><form id="l9zfn"></form></big></form>

<progress id="l9zfn"></progress>

<menuitem id="l9zfn"></menuitem>

<ruby id="l9zfn"></ruby>

<progress id="l9zfn"><meter id="l9zfn"></meter></progress><output id="l9zfn"><listing id="l9zfn"></listing></output>

歡迎訪問!詳細介紹各類輕質隔墻板的優勢和不足讓您只買對的不買貴的!

金領域建材銷售有限公司

—— 持續領航 品牌經營 ——

全國服務熱線

15515532955

輕質隔墻板物理性能-建筑用輕質隔墻條板圖集中文英文(四)

來源:未知   發布時間:2021-04-03 15:09nbsp;  點擊量:

中文版輕質隔墻板物理性能介紹:
5.5物理性能
物理性能應符合表5的規定
表5物理性能指標
板厚90mm
板原10
抗沖擊性能
經5次抗沖擊試驗后,板面無裂
抗彎承載(板自重倍數)
1,5
抗壓強度/MPa
面密度/(kg
含水率/%
干燥收縮
吊推力
0N置2(板面無超h.5m的數
不應出可的裂且考面無
A級
水石之系數為>0o不板的化系
夏熱冬
斯條板不檢
6試驗方法
6.1試驗環境及
試驗應在常溫
下進不
6.2外觀質量
6.2.1量具
鋼直尺,精度0,5m
6.2.2測量方法
對受測板,視距0.5m左右間測有無外露增強、貫通型(,泛霜;用鋼直尺量測板面裂健
的長度、窩氣孔、缺校掉角數據,讀數至1m,用刻度放大慢量測裂健的寬度,并記錄塊陷數量
6.3尺寸允許偏差
6.3.1量具
鋼卷尺精度1mm游標卡尺0~150mm;鋼直尺精度0.5mma內外卡錯、塞尺0~10mm靠尺2m
6.3.2測量方法
6.3.2.1長度
量測三處
一板邊兩處:靠近兩板邊100mm范國內,平行于該板邊
板中一處:過兩板端中點,如圖2所示。

Introduction to physical properties of lightweight partition board
5.5 physical properties 
 
 physical properties shall comply with the provisions of table 5 
 
 physical property index of table 5 
 
 plate thickness 90mm 
 
 original 10 
 
 impact resistance 
 
 after five impact tests, the plate surface has no crack 
 
 bending capacity (plate weight multiple) 
 
 1, 5) compressive strength / MPa (compressive strength / 
MPA) surface density / (kg 13; water content / / (kg 
 
 moisture content /% 
 
 drying shrinkage 
 
 lifting thrust 
 
 0n place 2 (plate surface has no super number of h.5m 
 
 there should be no cracks and no test surface has no grade a 
 
 grade a 
 
 grade of water stone coefficient is the coefficient of water 
stone is the coefficient of water is the coefficient of no board 
is the chemical system of no board chemical system of no 
board summer hot summer hot winter is hot winter is hot 
winter is the strip board is not inspected 
 
 strip is not inspected 
 
 6 test method 
 
 6.1 test environment and the test should be carried out at 
room temperature, under normal temperature, the 
appearance quality, the appearance quality, the appearance 
quality, the appearance quality, the appearance quality, the 
measuring tool, steel ruler, steel ruler, steel ruler, precision, 
precision, precision, precision, precision, precision, precision, 
precision, precision, precision, precision, precision 6.2.2 
measurement method 
 
 for the plate under test, Measure whether there is exposed 
reinforced, through type (, frosting) between the sight 
distance of about 0.5m; use steel ruler to measure the length, 
dimple hole, missing angle data of the plate surface crack 
key, read to 1m, enlarge the scale slowly to measure the 
width of the crack key, and record the number of blocks 
 
 6.3.1 measuring tool 
 
 steel tape precision 1mm vernier caliper 0 ~ 150mm; 
Accuracy of steel ruler is 0.5mma, internal and external error, 
feeler gauge is 0 ~ 10mm, guiding rule is 2m 
 
 6.3.2 measuring method 
 
 6.3.2.1 length 
 
 measuring three places 
 
 one plate edge two places: within the range of 100 mm near 
two plate edges, parallel to the plate edge 
 
 one place in the plate: passing through the midpoint of two 
plate ends, as shown in Figure 2
 
微信二維碼 微信二維碼
聯系我們

電話:15515532955
手機:15515532955
Q Q:2424904545
郵箱:2424904545@qq.com

Copyright ? 2012-2020 金領域建材銷售有限公司< 版權所有

備案號:豫ICP備15033061號-2

chian少妇